MZ@ !L!This program cannot be run in DOS mode. $Rؕ3}3}3}H̴3}H̱3}Rich3}PEL!  6P}f@4.rsrc@6@@0Hf h8lPh[ (@EXFpGL        0 @ P ` p        (L4<ptlP&F(D(/R|56T6`@7N9>b>phA|MUIQkhqjan]]N.BEqy MUIen-USxUSB Hub Power ExceededMS Shell DlgHd2 &ResetPd2&CloseP'The indicated device requires more power than is available through the hub into which it is plugged.PP%2RecommendationP0"xUSB Controller Resources ExceededMS Shell DlgPd2&CloseP'PP%2RecommendationP0"@@_DeviceMS Shell DlgPwPower required: 0 mAP%wBandwidth currently in use: 0 %P3Device Information@PowerMS Shell DlgP6Hub informationPThe hub is self-poweredP(Total Power Available: PFA&Attached devices:PRISysListView32List1PxTo update the list, click Refresh.P2&RefreshH2&ClosexMaximum Hub Number SurpassedMS Shell DlgH2 &ResetPd2&CloseP'PP%2RecommendationP0"@AdvancedMS Shell DlgP6Hub informationPHub is operating at high speed: @1Hub has a single TT@F}&Devices consuming hub bandwidth:@PZSysListView32List1@&To update the list, click Refresh.@2&RefreshP2Reset &HubOThe unused ports shown in bold type belong to hubs that can support the device.jThe devices shown in bold type can be supported by the hub to which the under-powered device is connected.5The hub does not have enough power to support the %s.5The hub does not have enough power to support the %s.aDisconnect the %s from its current port and switch it with one of the devices shown in bold type.YConnect a power supply to the hub, or try reconnecting the %s to unused ports on your PC.The hub is self-powered.The hub is bus powered.PThe devices shown in bold type are attached to hubs that can support the device.Disconnect the %s from its current port and switch it with one of the devices shown in bold type. Note that the switched device may not work correctly.%d mAPower Required%d port(s) available&Total power available: %d mA per portPower required: %d mA The hub is not working properly. My ComputeriSituation resolved: the %s is now connected to a hub that does have enough power available to support it.iThe %s has malfunctioned and exceeded the power limits of its hub port. You should disconnect the device.PADisconnect the device, and click "Reset." If you click "Close," the port will not work until you unplug it and restart your PC.oA USB device has malfunctioned and exceeded the power limits of its hub port. You should disconnect the device.Power surge on the USB portaThe port didn't reset, but may continue to function. If it doesn't work, please restart your PC.-%s needs more power than the port can supply.-%s needs more power than the port can supply.dThe last USB device you connected to this computer malfunctioned, and Windows does not recognize it.mTry reconnecting the device. If Windows still does not recognize it, your device may not be working properly.USB device not recognizeddThe last USB device you connected to this computer malfunctioned, and Windows does not recognize it.>The controller does not have enough resources for this device.>The controller does not have enough resources for this device.Try connecting your device to a different port on your PC, or disconnect a device you are not using. Your PC manufacturer can provide more information.The table below shows you how much bandwidth each USB controller is using. Each USB controller has a fixed amount of bandwidth, which all attached devices must share.The devices listed below are being used by programs and are consuming bandwidth. To obtain updated bandwidth information, click Refresh.wTo free bandwidth, close the programs using these devices. If the programs cannot be found, unplug one or more devices.Bandwidth Used#Not enough USB controller resources!Bandwidth currently in use: %d%%System reservedPA Description ControllerDeviceNot enough power on the USB hubUniversal Serial Bus ErrorUnknown Unused PortUnknown USB DeviceUSB HubUSB Host ControllerHI-SPEED USB HubUnused Mini-PortToo many USB hubs are connected together. A USB hub will not function when it's connected more than 5 hubs away from the root port.Too many USB hubsToo many USB hubs are connected together. A USB hub will not function when it's connected more than 5 hubs away from the root port.PAVSituation resolved: the %s is now connected to a hub that is close enough to the root.eThe hub's location is highlighted below. The devices shown in bold type can be switched with the hub.fDisconnect the hub from its current location and switch it with one of the devices shown in bold type.UThe hub's location is highlighted below. Hubs with free ports are shown in bold type."Reconnect the %s to an unused hub.dThe hub's location is highlighted below. The hubs shown in bold type have enough power for this hub. (%d ports)Attached Devices BW ConsumedHub is operating at high-speedHub is operating at full-speedHub has multiple TTsHub has a single TTPort Number %dPA USB settings1Specify USB power settings for the USB hub driverUSB selective suspend setting9Specify whether USB selective suspend is turned on or offEnabledEnable USB selective suspendDisabled#Do not enable USB selective suspend3Device can perform faster when connected to USB 3.0Connected to USB 3.0|4VS_VERSION_INFO@%@%?StringFileInfo040904B0LCompanyNameMicrosoft Corporation> FileDescriptionUSB UI Dllr)FileVersion6.3.9600.16384 (winblue_rtm.130821-1623),InternalNameUsbui.LegalCopyright Microsoft Corporation. All rights reserved.DOriginalFilenameUsbui.dll.muij%ProductNameMicrosoft Windows Operating SystemBProductVersion6.3.9600.16384DVarFileInfo$Translation PADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPAD